United Security Products AVD-45c Manuál Strana 129
- Strana / 302
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
1/03 UDC 6300 Process Controller Product Manual 115
4.11 Control Parameters Set Up Group, Continued
Table 4-10 Control Group Definitions, continued
Lower Display
Prompt
Upper Display
Range of Setting
or Selection
Parameter
Definition
OUT HYST
0.0 to 5.0% of PV Span
HYSTERESIS (OUTPUT RELAY) is an adjustable
overlap of the ON/OFF states of each control output.
This is the difference between the value of the
process variable at which the control outputs
energize and the value at which they de-energize.
Only applicable for ON/OFF control.
FAIL MODE
NON LATCH
LATCHING
FAILSAFE MODE
NON LATCH - when the controller has gone to
failsafe and the problem is corrected, the controller
will go to automatic mode on power up at the
setpoint that was being used.
LATCHING - When the controller has gone to
failsafe and the problem is corrected, the controller
will stay in manual mode.
FAILSAFE
0 to 100%
FAILSAFE OUTPUT VALUE — The value used
here will also be the output level when you have
Communications SHED or when NO BURNOUT is
configured and Input 1 fails.
PBorGAIN*
PROPORTIONAL BAND UNITS — Select one of
the following for the Proportional (P) term of the PID
algorithm:
PB PCT
PROPORTIONAL BAND — Selects units of percent
proportional band for the P term of the PID
algorithm.
Where: PB% = 100%FS
GAIN
GAIN
GAIN selects the unitless term of gain for the P term
of the PID algorithm.
Where: GAIN =100%FS
PB%
MINorRPM*
RESET UNITS — Selects units of minutes or repeat
per minutes for the I term of the PID algorithm. 20
Repeats per Minute = 0.05 Minutes per Repeat.
RPM
REPEATS PER MINUTE — The number of times
per minute that the proportional action is repeated by
reset.
MINUTES
MINUTES PER REPEAT — The time between each
repeat of the proportional action by reset.
*Selection here is used for both Loop 1 and Loop 2 if available. Also applies to Gain Scheduling on Loops 1 and 2.
- UDC 6300 1
- Process Controller 1
- Product Manual 1
- About This Publication 3
- Table of Contents 5
- Table of Contents, continued 5
- Figures 8
- Tables 9
- Tables, continued 10
- Acronyms 12
- References 13
- Section 1 – Overview 15
- 1.1 Introduction 15
- 1.1 Introduction, Continued 16
- 1.2 Operator Interface 18
- Table 1-1 Function of Keys 19
- Section 2 – Installation 21
- 2.1 Overview 21
- 2.1 Overview, Continued 22
- Model number 23
- 24Vac/dc 115 Vac 230 Vac 25
- POWER SELECT JUMPER PLACEMENT 25
- 2.4 Mounting 27
- 2.4 Mounting, Continued 28
- 2.5 Wiring 29
- 2.5 Wiring, Continued 30
- 2.6 Wiring Diagrams 31
- Line voltage wiring 32
- High level input 33
- Optional Input 5 34
- (Low Level Inputs) 34
- Current Output 36
- 2nd Current Output 4–20mA 37
- Section 3 – Configuration 41
- 3.1 Overview 41
- 3.2 Configuration Prompts 42
- CYC4SEC PVEU VALx GAIN VALx 43
- 3.3 How To Get Started 44
- 3.4 Configuration Tips 45
- 3.5 Configuration Procedure 46
- Set this group last 48
- Duplex Heat Cool 48
- Loop) 52
- 3.9 Accutune Set Up Group 54
- 3.17 Options Set Up Group 72
- 3.18 Communications Group 74
- 3.19 Alarms Set Up Group 76
- (Process Variable) 77
- (Communications) 77
- 3.21 Calib Group 80
- 3.22 Status Group 80
- Keep a record 81
- 4.1 Overview 85
- 4.5 Accutune Set Up Group 93
- ATTENTION 100
- PV (or RSP) = K x 102
- (A - B) 104
- (Calc Hi - Calc Lo)) 104
- PV or SP = K 104
- Continued 109
- Continued on next page 109
- LT A or B GT A 115
- These prompts appear only 117
- 4.13 Options Set Up Group 134
- Introduction 142
- Communications group 142
- 4.15 Alarms Set Up Group 147
- 4.17 Calibration Data 155
- 4.18 Status Test Data 155
- Section 5 – Operation 157
- 5.1 Overview 157
- Lower Display 159
- Upper Displa 159
- 5.3 Enter a Security Code 160
- Operator Interface 161
- Decimal point 161
- Annunciators 162
- Bargraphs 163
- Setpoint Bargraph 163
- Σ (Sigma) 165
- 5.5 Start Up Procedure 167
- 5.6 Operating Modes 168
- Upper Display 170
- continued 171
- CONTROL2 172
- 5.7 Setpoints, Continued 175
- 5.8 Setpoint Rate 179
- 5.9 Single Setpoint Ramp 180
- Available selections 183
- The switchover 184
- The PV value 185
- X= 1 or 2 185
- Single Loop 187
- Controller 187
- Loop 2 188
- Internal Cascade 189
- Override rules 190
- Table 5-25 191
- Parameters 193
- Internal cascade 196
- 5.15 Input Math Algorithms 198
- Totalizer function 200
- 5.16 Logic Gate Operation 201
- 5.17 Digital Outputs 203
- How it works 212
- Configuration 212
- 5.20 Accutune™ 213
- 5.20 Accutune™, Continued 214
- 5.21 Input 5 - Pulse Input 222
- OUT and the estimated 3PStep 225
- 5.23 Auto/Manual Station 226
- Description 227
- Input 1 Span 228
- Input 2 Span 228
- Operation 229
- 6.1 Overview 231
- (IEC=0.00385) 232
- Disconnect the field 233
- 1 to 5 Volts or 4–20 235
- X = 1, 2, 3, or 4 236
- INX SPAN 237
- Junction 240
- Resistor 240
- Precision 241
- RTD Inputs 242
- Radiamatic, Millivolts 243
- Volts, or milliamps 243
- Equipment needed 246
- Range Specifications 246
- IN5 SPAN 248
- 7.1 Overview 255
- 7.3 2nd Current Output 259
- CUR OUT2 261
- WARNING—SHOCK HAZARD 263
- 8.1 Overview, Continued 264
- 8.2 Troubleshooting Aids 265
- Software 266
- FAILSAFE 267
- 8.4 Status Tests 268
- Table 8-5 Status Tests 269
- (Lower Display) 270
- 8.5 Background Tests 271
- Output(s) failure 276
- Failure 276
- (Key Name) 278
- Rear of case 281
- Parts Identification 282
- (Part Number 30757007-501) 283
- (Part Number 30757071-501) 283
- Part Number 30757010-501) 283
- 8.9 Maintenance 291
- Section 9 – Parts List 293
- 9.1 Exploded View 293
- (opening must be widened) 295
Související produkty a manuály pro Systémy intercom pro domy United Security Products AVD-45c
(410 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce